Quick loading, high travel speeds and the ability to load and dump on the run yield fast cycle times, allowing Cat Wheel Tractor-Scrapers to consistently deliver high productivity at the lowest cost per ton.
Flywheel Power - Tractor/Scraper | — |
Scraper Capacity - Heaped | — |
Top Speed - Loaded | — |
Top Speed - Loaded | — |
180° Curb-to-Curb Turning Width | — |
Width - Cut | — |
Maximum Depth of Cut | — |
Tires - Scraper | 37.25R35**E3 |
Overall Width | — |
Scraper Capacity - Struck | — |
Scraper Capacity - Heaped | — |
Tires - Tractor | 37.25R35**E3 |
Fuel Tank Refill Capacity - Scraper | — |
Rated Load | 37 200 kg (82,200 lb); 37.2 tonnes (41.1 tons) |
Overall Shipping Height | — |
Maximum Depth of Spread | — |
Engine Model - Tractor | Cat C18 |
Rated Engine RPM - Tractor | — |
Flywheel Power - Tractor | — |
Emissions | Cat C18 engine meets U.S. EPA Tier 4 Final/EU Stage IV emission standards. |
Flywheel Power - Tractor/Scraper | — |
Scraper Capacity - Heaped | — |
Top Speed - Loaded | — |
Hydraulic System | — |
Transmission System | — |
Cooling System | — |
Diesel Exhaust Fluid (DEF) | — |
Fuel Tank | — |
Crankcase - Tractor | — |
Front of Tractor to Front Axle | — |
Axle to Vertical Hitch Pin | — |
Wheel Base | — |
Rear Axle - Rear of Machine | — |
Width - Inside of Bowl | — |
Ground Clearance - Tractor | — |
Length - Maximum (Push-Pull) | — |
Width - Rear Tire Centers | — |
Height - Scraper Blade Maximum | — |
Width - Outside Rear Tires | — |
Length - Overall Machine - Standard | — |
Width - Overall Machine | — |
Height - Top of Cab | — |
Width - Tractor | — |
Height - Overall Shipping | — |
Operating Weight - Empty | — |
Overall Length | — |
Overall Length - With Bail Down | — |
Operating Weight - Empty | — |
ROPS/FOPS | ROPS/FOPS meet “ISO Standards.” |
Exterior Sound Level | The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A). |
Seat Belt | SAE J386:FEB2006 |
Falling Object Protective Structure (FOPS) | ISO 3449:2005 Level II |
Rollover Protection Structure (ROPS) | ISO 3471:2008 for up to 21 282 kg (46,919 lb) |
Brakes | ISO 3450:2011 |
Steering System | ISO 5010:2007 |
Reverse Alarm | ISO 9533:2010 |
Transmission Gear - Reverse | — |
Transmission Gear - Sixth | — |
Transmission Gear - First | — |
Transmission Gear - Second | — |
Transmission Gear - Seventh | — |
Transmission Gear - Fifth | — |
Transmission Gear - Third | — |
Transmission Gear - Eighth | — |
Transmission Gear - Fourth | — |
Apron Raise | — |
Ejector Extend | — |
Bowl Lower | — |
Ejector Retract | — |
Bail Raise | — |
Bowl Raise | — |
Apron Lower | — |
Bail Lower | — |
• Up to 8% improvement in productivity.
• Advanced productivity electronic control system (APECS) allows
the engine and transmission to communicate on a high level. This
communication allows the machine to better utilize the power and torque the engine is producing. The net result is moving more material.
• Use ground speed control to set the desired top speed and the
machine will find the gear that works best for the engine and the transmission, providing a lower fuel burn.
• The machine speed limit feature replaces top gear selection, allowing the machine to find the correct gear that works best for the engine and transmission. Pulling the load in the correct gear, in most cases, results in lower engine load factor and lower fuel burn.
• Auto-stall assists in quickly bringing the transmission to an operating temperature at startup when the machine is working in a cold climate region.
• Cat®Payload Estimator for scrapers is an earthmoving solution for optimal payload and jobsite efficiency. Payload Estimator achieves on-the-go weighing by using bowl lift cylinder pressure during the loaded haul segment. Payload Estimator is optimized to be used with sequence assist, which provides increased productivity with
less operator effort. Payload Estimator is an automatic feature
when ordered with sequence assist.
• Reduce up to 14 individual operator commands per cycle with sequence assist (optional attachment).
• Steer with less effort using the newly designed high-pressure
steering system.
• Enjoy interior improvements and a more ergonomic workenvironment a 21% larger cab than the G Series cab.
• Intuitive, ergonomic controls keep operators focused on their work.
• Maintain desired cab temperature with automatic temperature
control.
• Get in and out of the cab easier with the new powered access
ladder system (optional attachment).
• Enhance an operator’s awareness of site surroundings with the optional work area vision system (WAVS).
• Seat belt indicator provides visual and audible alerts when the seat
belt is not in use.
• Advanced cushion hitch allows the cushion hitch to prevent end stroke by having the ability to predict end stroke events and manage the rate of dampening, resulting in reduced hitch maintenance and improved operator ride in rough conditions.
• Easy ground level access to fuel, water, and engine oil.
• The spacious cab features easy, intuitive controls and excellent
visibility. The cab provides a comfortable working environment for
all-day operation.
• Cat advanced ride management (ARM) seat suspension reduces
end stroke movement of the load cylinder for a smoother ride.
• Engine overspeed protection will automatically engage with no
operator input when the machine is in eighth gear. The machine will assist in slowing the machine speed by canceling the throttle command and engaging the engine compression brake.
• Monitor, manage, and enhance jobsite operations.
• Hit target grade faster and more accurately with Cat Grade
technologies. Finish jobs in fewer passes and with less operator effort, saving you time and helping to increase profit.
• Product Link™ collects machine data that can be viewed online
through web and mobile applications (optional attachment).• Access information anytime, anywhere with VisionLink®– useit to make informed decisions that boost productivity, lower costs, simplify maintenance, and improve safety and security on your jobsite.
• Shorten the learning curve for inexperienced operators with load
assist (optional attachment).
• The new tractor hydraulic on-demand fan helps assist in lowering fuel consumption.
• Using draft-arm overflow guards diverts material away from the bowl, preventing material from getting caught between the draft arms and the bowl sides.
• Cat Grade Control (optional attachment) intelligently ensures the
machine does not cut below grade in a cut area or overfill in thefill area.
Data not available.